AGA GC Podręcznik Użytkownika Pobierz pdf (Strona 7)

In the event of a power failure, the AIMS controls will not work until the power is restored. You

can still use your appliance as a conventional AGA.

TO LIGHT THE BURNER

CAUTION: BEFORE LIGHTING: ENSURE KNOB (A) IS IN THE OFF POSITION (SEE FIG. 5).

ALSO ENSURE GAS SUPPLY TO COOKER IS ON, AND THE GAS SERVICE COCK (C) IS

IN THE ON POSITION (SEE FIG. 3), AND THE ELECTRICITY SUPPLY TO THE AGA IS

SWITCHED ON.

LIGHTING PROCEDURE - SEE FIGS. 4 - 10

1. The main burner gas flow is set with the ‘temperature’ knob (B) (See Fig. 4). First, ensure

both knobs are turned fully clockwise. Knob (A) to the OFF position and knob (B) to the

minimum setting (See Fig. 4).

2. Turn ON/OFF knob (A) slightly anti-clockwise towards the IGNITION position ( ) until

reaching stop, press down and hold for 5 seconds (gas flows only to the pilot burner). (See

Fig. 6).

3. Continue pressing down knob (A) while turning further anti-clockwise to the PILOT position

(this activates the piezo), continue to hold down for 10 seconds after pilot burner has been lit.

(If the pilot does not light, steps 2 and 3 can be repeated). (See Fig. 7).

4. Upon lighting, release knob and turn further anti-clockwise to the ON position (large flame

symbol) (See Fig. 8). Pilot gas flows and mains gas flows according to the temperature

setting (knob B).

5. Turn the temperature knob (B) slightly anti-clockwise into the white band (LOW FIRE

position). Leave in the low fire position for at least 30 minutes

(See Fig. 9).

NOTE: ‘LOW FIRE’ position is attained by turning knob (B) gradually into the white band, until

SMALL FLAME is observed through viewing window (H). (See Fig. 3).

6. After 30 minutes rotate control knob (B) anti-clockwise to the mid-position of the green band

for normal running. (See Fig. 10).

NOTE: After several hours the heat indicator should be within the black band on the AIMS

handset ‘INFORMATION’ screen. It may be necessary to adjust the control knob slightly in the

green band to achieve this, allow the cooker to stabilise for at least 4 hours before attempting

any further adjustment.

When the cooker is lit from cold, moisture may form on the enamel which should be wiped off to

prevent staining.

IF THE FLAME HAS EXTINGUISHED FOR WHATEVER REASON, WAIT THREE MINUTES

(MINIMUM) BEFORE RE-LIGHTING.

NOTE: IF THE PILOT EXTINGUISHES

For safety purposes a flue safety device (6) is fitted.

This will only operate in adverse flue conditions, it should be checked and if necessary

depressed. If this problem persists contact your local engineer to determine and rectify the

cause.

TO EXTINGUISH THE BURNER

1. Turn ON/OFF knob (A) clockwise until reaching stop (PILOT) position.

2. Press down slightly and continue turning clockwise from pilot position to the OFF position

(See Fig. 5).

NOTE: LPG APPLIANCE ONLY. When the cooker is turned off a noticeably loud pop will

be heard. This is quite normal.

When the burner has cooled sufficiently, pilot lighting procedure may be repeated.

POWER FAILURE (OPEN FLUE MODELS ONLY)

1 2 3 4 5 6 7 8 9 10 11 12 ... 23 24

Komentarze do niniejszej Instrukcji

Brak uwag

AGA GC Podręcznik Użytkownika Strona 7

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Małe urządzenia kuchenne AGA GC